From Fedora Project Wiki
Line 384: Line 384:
  
 
Shut down the HiFive board, remove the SD card, and copy the 4th partition from the SD card into a file or partition on the NBD server.
 
Shut down the HiFive board, remove the SD card, and copy the 4th partition from the SD card into a file or partition on the NBD server.
 +
 +
You will need to change the UUID on this filesystem to a new random one (else it will conflict with the SD-card root filesystem), eg:
 +
<pre>
 +
tune2fs -U random /dev/VG/jive
 +
</pre>
  
 
Start up the NBD server (in this example using <code>qemu-nbd</code> with the 4th partition having been copied to <code>/dev/VG/jive</code> listening on port 10810):
 
Start up the NBD server (in this example using <code>qemu-nbd</code> with the 4th partition having been copied to <code>/dev/VG/jive</code> listening on port 10810):

Revision as of 14:52, 28 February 2020

This page describes the steps necessary to get Fedora for RISC-V running, either on emulated or real hardware.

Obtain a disk image

Tested images

These images have undergone some testing and thus are more likely to work without issues. If you are not sure which image to choose, go with one of these.

Download using virt-builder

This is the recommended way to obtain disk images.

Before you can start using virt-builder for this task, a one-time setup is necessary:

$ mkdir -p ~/.config/virt-builder/repos.d/
$ cat <<EOF >~/.config/virt-builder/repos.d/fedora-riscv.conf
[fedora-riscv]
uri=https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/index
EOF

With that out of the way, you can get a list of available RISC-V templates with:

$ virt-builder --list | grep riscv64
fedora-rawhide-developer-20191123.n.0   riscv64   Fedora® Rawhide Developer 20191123.n.0
fedora-rawhide-minimal-20191123.n.1     riscv64   Fedora® Rawhide Minimal 20191123.n.1

Then tell virt-builder to build a custom disk image based on one of the templates:

$ virt-builder \
  --arch riscv64 \
  --size 20G \
  --format raw \
  --output Fedora-Developer-Rawhide-20191123.n.0-sda.raw \
  fedora-rawhide-developer-20191123.n.0
[   3.6] Downloading: https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/Fedora-Developer-Rawhide-20191123.n.0-sda.raw.xz
[   6.1] Planning how to build this image
[   6.1] Uncompressing
[  32.8] Opening the new disk
[  38.4] Setting a random seed
[  38.4] Setting the machine ID in /etc/machine-id
[  38.4] Setting passwords
virt-builder: Setting random password of root to 5PegnZtGMP47bXnw
[  39.9] Finishing off
                   Output file: Fedora-Developer-Rawhide-20191123.n.0-sda.raw
                   Output size: 20.0G
                 Output format: raw
            Total usable space: 19.7G
                    Free space: 14.7G (75%)

virt-builder has reasonable defaults, such as generating a random root password for you, but if you want more control you can pass additional arguments to customize the image further: for example, using --format qcow2 will cause the output image to be in QCOW2 format. See virt-builder --help for more information.

In addition to the disk image, a firmware image (which has to be downloaded separately) is needed as well. To find out the download URL, use:

$ virt-builder --arch riscv64 --notes fedora-rawhide-developer-20191123.n.0 | grep fw_payload
https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/Fedora-Developer-Rawhide-20191123.n.0-fw_payload-uboot-qemu-virt-smode.elf
https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/Fedora-Developer-Rawhide-20191123.n.0-fw_payload-uboot-qemu-virt-smode.elf.CHECKSUM

Then download it using your favorite HTTP client, for example:

$ wget https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/Fedora-Developer-Rawhide-20191123.n.0-fw_payload-uboot-qemu-virt-smode.elf

Download manually

If using virt-builder is not an option, you can download disk images manually from: https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/

Download Fedora-Developer-Rawhide-*.raw.xz as well as the matching Fedora-Developer-Rawhide-*-fw_payload-uboot-qemu-virt-smode.elf.

Nightly builds

You can find them here: http://fedora.riscv.rocks/koji/tasks?state=closed&view=flat&method=createAppliance&order=-id

Select the most recent (top) build and download Fedora-Developer-Rawhide-*.raw.xz.

These disk images differ from the ones above in that:

  • the firmware is inside the disk image, in the /boot directory;
  • they are completely untested.

Prepare the disk image

These steps are only necessary if you haven't used virt-builder.

Uncompress the image

Whether you have downloaded a tested image or a nightly build, you'll need to uncompress it before it can be used:

$ unxz Fedora-Developer-Rawhide-*.raw.xz

Optional: expand the disk image

You might want to expand the disk image before setting up the VM. Here is one example:

$ truncate -r Fedora-Developer-Rawhide-*.raw expanded.raw
$ truncate -s 40G expanded.raw
$ virt-resize -v -x --expand /dev/sda4 Fedora-Developer-Rawhide-*.raw expanded.raw
$ virt-filesystems --long -h --all -a expanded.raw
$ virt-df -h -a expanded.raw

The resulting disk image will work with QEMU as well as TinyEMU. Make sure you use expanded.raw instead of Fedora-Developer-Rawhide-*.raw when booting the guest.

Optional: create an overlay

You can also create qcow2 disk image with raw Fedora disk as backing one. This way Fedora raw is unmodified and all changes are written to qcow2 layer. You will need to install libguestfs-tools-c.

$ qemu-img create -f qcow2 -F raw -b Fedora-Developer-Rawhide-*.raw overlay.qcow2 20G
$ virt-resize -v -x --expand /dev/sda4 Fedora-Developer-Rawhide-*.raw overlay.qcow2
$ virt-filesystems --long -h --all -a overlay.qcow2

The resulting disk image will only work with QEMU. Make sure you use overlay.qcow2 instead of Fedora-Developer-Rawhide-*.raw when booting the guest.

Optional: set the hostname before booting

If you want to change hostname before the first boot, install libguestfs-tools-c and then run:

$ virt-customize -a Fedora-Developer-Rawhide-*.raw --hostname fedora-riscv-mymagicbox

Nightly builds only: extracting firmware (OpenSBI)

Fedora/RISC-V does not support BLS (Boot Loader Specification - more details).

Disk images contain a /boot directory from where you can copy out the firmware.

This is only necessary for nightly builds, since for tested images these files are provided as separate downloads alongside the image.

Example session:

$ guestfish \
  add Fedora-Developer-Rawhide-*.raw : \
  run : \
  mount /dev/sda1 / : \
  ls /opensbi/unstable
fw_jump.elf
fw_payload-5.2.0-0.rc7.git0.1.0.riscv64.fc31.riscv64.elf
fw_payload-uboot-qemu-virt-smode.elf
$ guestfish \
  add Fedora-Developer-Rawhide-*.raw : run : mount /dev/sda1 / : \
  download /opensbi/unstable/fw_payload-uboot-qemu-virt-smode.elf fw_payload-uboot-qemu-virt-smode.elf

You can also use guestmount or QEMU/NBD to mount disk image. Examples:

$ mkdir a
$ guestmount -a $PWD/Fedora-Developer-Rawhide-*.raw -m /dev/sda1 $PWD/a
$ cp a/opensbi/unstable/fw_payload-uboot-qemu-virt-smode.elf .
$ guestunmount $PWD/a
$ sudo modprobe nbd max_part=8
$ sudo qemu-nbd -f raw --connect=/dev/nbd1 $PWD/Fedora-Developer-Rawhide-*.raw
$ sudo fdisk -l /dev/nbd1
Disk /dev/nbd1: 7.5 GiB, 8053063680 bytes, 15728640 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: F0F4268F-1B73-46FF-BABA-D87F075DCCA5

Device      Start      End  Sectors  Size Type
/dev/nbd1p1  2048 15001599 14999552  7.2G Linux filesystem
$ sudo mount /dev/nbd1p1 a
$ sudo cp a/opensbi/unstable/fw_payload-uboot-qemu-virt-smode.elf .
$ sudo umount a
$ sudo qemu-nbd --disconnect /dev/nbd1

Note NBD is highly useful if you need to run fdisk, e2fsck (e.g. after VM crash and filesystem lock up), resize2fs. It might be beneficial to look into nbdkit and nbd packages.

Boot the image on virtual hardware

There are several options for booting the image on virtual hardware once you've prepared it following the steps above.

Boot with libvirt

Detailed instructions how to install libvirt: https://docs.fedoraproject.org/en-US/quick-docs/getting-started-with-virtualization/

Quick instructions for libvirt installation (tested on Fedora 30):

# dnf group install --with-optional virtualization
# systemctl enable --now libvirtd

When running RISC-V guests, it's usually a good idea to use the very latest versions of QEMU, libvirt and virt-manager: the virt-preview repository offers just that for Fedora users. To enable it, simply run:

# dnf copr enable @virtmaint-sig/virt-preview

and update your system.

The steps below assume you have copied both the disk image and the firmware into /var/lib/libvirt/images: this is the location where libvirt usually expects to find disk images, so while using a different location might work it's a good idea to do this and reduce the possibility of issues caused by filesystem permissions and such.

Assuming you have QEMU ≥ 4.0.0, libvirt ≥ 5.3.0 and virt-manager ≥ 2.2.0, the installation will be as simple as:

# virt-install \
  --name fedora-riscv \
  --arch riscv64 \
  --vcpus 8 \
  --memory 2048 \
  --os-variant fedora30 \
  --boot kernel=/var/lib/libvirt/images/Fedora-Developer-Rawhide-*-fw_payload-uboot-qemu-virt-smode.elf \
  --import --disk path=/var/lib/libvirt/images/Fedora-Developer-Rawhide-*.raw \
  --network network=default \
  --graphics none

If you are stuck with older software (QEMU ≥ 2.12.0, libvirt ≥ 4.7.0), then you're going to need a more verbose command line:

# virt-install \
  --name fedora-riscv \
  --arch riscv64 \
  --machine virt \
  --vcpus 8 \
  --memory 2048 \
  --os-variant fedora30 \
  --boot kernel=/var/lib/libvirt/images/Fedora-Developer-Rawhide-*-fw_payload-uboot-qemu-virt-smode.elf \
  --import --disk path=/var/lib/libvirt/images/Fedora-Developer-Rawhide-*.raw,bus=virtio \
  --network network=default,model=virtio \
  --rng device=/dev/urandom,model=virtio \
  --channel name=org.qemu.guest_agent.0 \
  --graphics none

Additionally, when using older software components you won't get PCI support, and so enabling graphics will not be possible.

Either one of the commands above will automatically boot you into the console. If you don't want that add --noautoconsole option. You can later use virsh tool to manage your VM and get to console.

A quick reference of virsh commands:

  • virsh list --all - list all VMs and their states
  • virsh console <name> - connect to serial console (remember: Escape character is ^])
  • virsh shutdown <name> - power down VM (see above for more details)
  • virsh start <name> - power up VM
  • virsh undefine <name> - remove VM
  • virsh net-list - list network (useful for the next command)
  • virsh net-dhcp-leases <network_name> - list DHCP leases, <network_name> most likely will be default. This is useful when you want to get IPv4 and SSH to the VM.
  • virsh domifaddr <name> - alternative for the above two commands, only shows IPv4 for one VM
  • virsh reset <name> - hard reset VM
  • virsh destroy <name> hard power down of VM

If you want to use ssh user@virtualMachine you can setup libvirt NSS module. See: https://wiki.libvirt.org/page/NSS_module

You might want also to setup logging for serial console (in case kernel panics or something else).

For this we will be using two commands: virsh edit <name> (modifying VM XML) and virsh dumpxml <name> (dump VM XML for backup). You need to modify <serial> node by adding <log file='/var/log/libvirt/qemu/fedora-riscv-mymagicbox.serial.log'/>. Then power down and power up the VM.

Alternatively you can use --serial log.file=/.../whatever.serial.log with virt-install command.

Boot under QEMU

You will get the best results if your QEMU version is 4.0.0 or newer, but any version since 2.12.0 will work.

$ qemu-system-riscv64 \
  -nographic \
  -machine virt \
  -smp 8 \
  -m 2G \
  -kernel Fedora-Developer-Rawhide-*-fw_payload-uboot-qemu-virt-smode.elf \
  -object rng-random,filename=/dev/urandom,id=rng0 \
  -device virtio-rng-device,rng=rng0 \
  -device virtio-blk-device,drive=hd0 \
  -drive file=Fedora-Developer-Rawhide-*.raw,format=raw,id=hd0 \
  -device virtio-net-device,netdev=usernet \
  -netdev user,id=usernet,hostfwd=tcp::10000-:22

Once machine is booted you can connect via SSH:

$ ssh -p 10000 -o UserKnownHostsFile=/dev/null -o StrictHostKeyChecking=no -o PreferredAuthentications=password -o PubkeyAuthentication=no root@localhost

Boot under TinyEMU (RISCVEMU)

Note (2019 March 10): This is not supported anymore until TinyEMU is updated to support external initrd file. Please, use QEMU or libvirt/QEMU.

RISCVEMU recently (2018-09-23) was renamed to TinyEMU (https://bellard.org/tinyemu/).

TinyEMU allow booting Fedora disk images in TUI and GUI modes. You can experiment using JSLinux (no need to download/compile/etc) here: https://bellard.org/jslinux/

Below are instructions how to boot Fedora into X11/Fluxbox GUI mode.

Step 1. Compile TinyEMU:

wget https://bellard.org/tinyemu/tinyemu-2018-09-23.tar.gz
tar xvf tinyemu-2018-09-23.tar.gz
cd tinyemu-2018-09-23
make

Step 2. Setup for booting Fedora:

mkdir fedora
cd fedora
cp ../temu .

# Download pre-built BBL with embedded kernel
wget https://bellard.org/jslinux/bbl64-4.15.bin

# Create configuration file for TinyEMU
cat <<EOF > root-riscv64.cfg
/* VM configuration file */
{
    version: 1,
    machine: "riscv64",
    memory_size: 1400,
    bios: "bbl64-4.15.bin",
    cmdline: "loglevel=3 console=tty0 root=/dev/vda rw TZ=${TZ}",
    drive0: { file: "Fedora-Developer-Rawhide-*-sda1.raw" },
    eth0: { driver: "user" },
    display0: {
        device: "simplefb",
        width: 1920,
        height: 1080,
    },
    input_device: "virtio",
}
EOF

# Download disk image and unpack in the same directory

Step 3. Boot it.

./temu -rw root-riscv64.cfg

We need to use -rw if we want our changes to persist in disk image. Otherwise disk image will be loaded as read-only and all changes will not persist after reboot.

Boot the image on physical hardware

Install on the HiFive Unleashed SD card

The disk image can be copied directly to an SD card and run on the HiFive Unleashed board.

A good way to create the SD card is with this virt-builder command:

sudo virt-builder \
    --source https://dl.fedoraproject.org/pub/alt/risc-v/repo/virt-builder-images/images/index \
    --no-check-signature \
    --arch riscv64 \
    --format raw \
    --hostname testing.example.com \
    --output /dev/sdXXX \
    --root-password password:riscv \
    fedora-rawhide-developer-20200108.n.0

Install on the HiFive Unleashed using NBD server

You will need a separate machine on the same network which can act as an NBD server. It can be any Linux machine with qemu-nbd or nbdkit installed.

You will first need to get it working on the SD card using the instructions in the previous section.

On the HiFive board, install dracut-network and nbd, and rebuild the initramfs with NBD support using these commands:

dnf install dracut-network nbd
dracut -m "nbd network base" -v --force

Shut down the HiFive board, remove the SD card, and copy the 4th partition from the SD card into a file or partition on the NBD server.

You will need to change the UUID on this filesystem to a new random one (else it will conflict with the SD-card root filesystem), eg:

tune2fs -U random /dev/VG/jive

Start up the NBD server (in this example using qemu-nbd with the 4th partition having been copied to /dev/VG/jive listening on port 10810):

qemu-nbd -t -f raw -x "" -p 10810 /dev/VG/jive

Place the SD card back in the HiFive board and boot it. At this point you have still booted into the SD card's root filesystem (not NBD). Go and edit /boot/extlinux/extlinux.conf. To the addappend line you will need to set:

root=UUID=...uuid... netroot=nbd:192.168.0.220:10810 rootfstype=ext4 rw rootdelay=5 ip=dhcp rootwait

I would also advise removing rhgb quiet if they are present. Note you need to set uuid and the address and port number of the NBD server correctly. Immediately reboot and it should come up with an NBD root. Check the boot messages carefully to see whether it used the SD card or NBD root.

Install Fedora GNOME Desktop on SiFive HiFive Unleashed + Microsemi HiFive Unleashed Expansion board

Detailed instructions are provided by Atish Patra from Western Digital Corporation (WDC). See their GitHub page for details and pictures: https://github.com/westerndigitalcorporation/RISC-V-Linux

So far two GPUs are confirmed to be working: Radeon HD 6450 and Radeon HD 5450.

Use the image

Once the system is booted, login as root with riscv as password.

X11 with Fluxbox can be started using: startx /usr/bin/startfluxbox. The disk image also includes awesome and i3 for testing. Dillo is available as a basic web browser (no javascript support) and pcmanfm as file manager.

To gracefully shutdown just type poweroff into console.

If you want more information being displayed during boot, remove quiet from the append line in /boot/extlinux/extlinux.conf.