From Fedora Project Wiki

m (Docs/Virtualization Quick Start moved to Virtualization Quick Start: sticksters demands! :))
m (fixing admonitions)
Line 26: Line 26:
==== Requirements for Para-virtualized Guests ====
==== Requirements for Para-virtualized Guests ====


{{Admon/warning | Only Xen supports para-virtualized guests. KVM uses full virtualization.}}
{{Admon/note | Only Xen supports para-virtualized guests. KVM uses full virtualization.}}


Any x86_64, or ia64 CPU is supported for running para-virtualized guests with Xen. For i386 hardware, a CPU with the PAE extension is required. Many older laptops (particularly those based on Pentium Mobile / Centrino) do not have PAE support. To determine if a CPU has PAE support, run the following command:
Any x86_64, or ia64 CPU is supported for running para-virtualized guests with Xen. For i386 hardware, a CPU with the PAE extension is required. Many older laptops (particularly those based on Pentium Mobile / Centrino) do not have PAE support. To determine if a CPU has PAE support, run the following command:
Line 51: Line 51:
</pre>
</pre>


{{Admon/warning | On some Intel systems, virtualization support needs to be enabled in the BIOS. Please ensure that this has been done before proceeding.}}
{{Admon/caution | On some Intel systems, virtualization support needs to be enabled in the BIOS. Please ensure that this has been done before proceeding.}}


=== Installing the Virtualization Software ===
=== Installing the Virtualization Software ===
Line 94: Line 94:




{{Admon/warning | Note that for the default setup, networking for the guest OS (DomU) is bridged. This means that DomU's will get an IP address on the same network as Dom0. If a DHCP server provides addresses, it needs to be configured to give addresses to the guests. Another networking type can be selected by editing <code>/etc/xen/xend-config.sxp</code>}}
{{Admon/note | Note that for the default setup, networking for the guest OS (DomU) is bridged. This means that DomU's will get an IP address on the same network as Dom0. If a DHCP server provides addresses, it needs to be configured to give addresses to the guests. Another networking type can be selected by editing <code>/etc/xen/xend-config.sxp</code>}}


=== Configuring Remote Management ===
=== Configuring Remote Management ===
Line 213: Line 213:




{{Admon/warning | A valid URI must be passed to <code>virsh</code>. For details, see http://libvirt.org/uri.html}}
{{Admon/note | A valid URI must be passed to <code>virsh</code>. For details, see http://libvirt.org/uri.html}}


To start a virtual machine:
To start a virtual machine:
Line 346: Line 346:
There are two tools which can help greatly in accessing data within a guest disk image: ''lomount'' and ''kpartx''.
There are two tools which can help greatly in accessing data within a guest disk image: ''lomount'' and ''kpartx''.


{{Admon/warning | Remember never to do this while the guest is up and running, as it could corrupt the filesystem}}
{{Admon/caution | Remember never to do this while the guest is up and running, as it could corrupt the filesystem}}


* '''lomount'''
* '''lomount'''
Line 406: Line 406:
</pre>
</pre>


{{Admon/warning | Note: '''always''' remember to deactivate the logical volumes with "vgchange -an", remove the partitions with "kpartx -d", and (if appropriate) delete the loop device with "losetup -d" after performing the above steps. The default volume group name for a Fedora install is always the same, it is important to avoid activating two volume group of the same name at the same time.  LVM will cope as best it can, but it is not possible to distinguish between these two groups on the command line. In addition, if the volume group is active on the host and the guest at the same time, it can cause filesystem corruption.}}
{{Admon/caution | Note: '''always''' remember to deactivate the logical volumes with "vgchange -an", remove the partitions with "kpartx -d", and (if appropriate) delete the loop device with "losetup -d" after performing the above steps. The default volume group name for a Fedora install is always the same, it is important to avoid activating two volume group of the same name at the same time.  LVM will cope as best it can, but it is not possible to distinguish between these two groups on the command line. In addition, if the volume group is active on the host and the guest at the same time, it can cause filesystem corruption.}}


=== Getting Help ===
=== Getting Help ===

Revision as of 20:07, 10 August 2008

Previous Fedora Virtualization Guides can be found here:

Fedora7VirtQuickStart

Fedora8VirtQuickStart


Virtualization in Fedora

Fedora includes support for both the KVM and the Xen virtualization platforms. For more information on different virtualization platforms, see http://virt.kernelnewbies.org/TechComparison.

More information on Xen can be found at http://wiki.xensource.com/xenwiki/ and the Fedora Xen page. More information on KVM can be found at http://kvm.qumranet.com/kvmwiki.

Fedora is following the 3.0.x Xen line. Xen 3.0.0 was released in December of 2005 and is incompatible with guests using the previous Xen 2.0.x releases.

Quick Start

The following guide will explain how to set up Xen and KVM, and how to create and manage guests using either the command line or GUI interface.

System Requirements

  • For KVM, the system must have a CPU with virtualization support.
  • Sufficient storage space for the guest operating systems. A minimal command-line Fedora system requires around 600MB of storage, a standard desktop Fedora system requires around 3GB.
  • Generally speaking, at least 256 megs of RAM per guest plus 256 for the base OS. Practically speaking, it is hard to do work with virtualization with less than 1 GB of RAM.

Requirements for Para-virtualized Guests

Note.png
Only Xen supports para-virtualized guests. KVM uses full virtualization.

Any x86_64, or ia64 CPU is supported for running para-virtualized guests with Xen. For i386 hardware, a CPU with the PAE extension is required. Many older laptops (particularly those based on Pentium Mobile / Centrino) do not have PAE support. To determine if a CPU has PAE support, run the following command:

grep pae /proc/cpuinfo
flags           : fpu tsc msr pae mce cx8 apic mtrr mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow up ts

The above output shows a CPU that does have PAE support. If the command returns nothing, then the CPU does not have PAE support.

Fully-virtualized guests (HVM/Intel-VT/AMD-V)

To run fully virtualized guests in Xen or KVM, host CPU support is needed. This is typically referred to as Intel VT, or AMD-V. To check for Intel VT support look for the 'vmx' flag, or for AMD-V support check for 'svm' flag:

....For Intel....
grep vmx /proc/cpuinfo
flags           : fpu tsc msr pae mce cx8 apic mtrr mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx est tm2 cx16 xtpr lahf_lm

....For AMD....
grep svm /proc/cpuinfo
flags           : fpu tsc msr pae mce cx8 apic mtrr mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt rdtscp lm 3dnowext 3dnow pni cx16 lahf_lm cmp_legacy svm cr8_legacy
Stop (medium size).png
On some Intel systems, virtualization support needs to be enabled in the BIOS. Please ensure that this has been done before proceeding.

Installing the Virtualization Software

When doing a fresh install of Fedora, the virtualization packages can be installed by selecting Virtualization in the Base Group in the installer.

For an existing Fedora installation, the Xen kernel, KVM, and other virtualization tools can be installed by running the following command:

su -c "yum groupinstall 'Virtualization'"

Enter the root password when prompted.

This will install kvm, python-virtinst, qemu, virt-manager, virt-viewer and whatever dependencies are needed. Optional packages in this group are xen, gnome-applet-vm and virt-top.

Verify Virtualization is Enabled

Fedora supports multiple underlying Virtualization platforms. Verifying that Virtualization is enabled depends on which platform is being used. For example, when using KVM, the command to display all domains on the local system would be: virsh -c qemu:///system list. When using Xen,the command would be virsh -c xen:///system list.

To verify that Virtualization is enabled on the system, run the following command, where <URI> is a valid URI that libvirt can recognize. For more details on URIs: see http://libvirt.org/uri.html.

su -c "virsh -c <URI> list"
Name                              ID Mem(MiB) VCPUs State  Time(s)
Domain-0                           0      610     1 r----- 12492.1

The above output indicates that there is an active hypervisor. If Virtualization is not enabled an error similar to the following will appear:

su -c "virsh -c <URI> list"
libvir: error : operation failed: xenProxyOpen
error: failed to connect to the hypervisor
error: no valid connection

If the above error appears, make sure that:

  • For Xen, make sure that xend is running.
  • For KVM, make sure that libvirtd is running.
  • For either, make sure the URI is properly specified (see http://libvirt.org/uri.html for details).


Note.png
Note that for the default setup, networking for the guest OS (DomU) is bridged. This means that DomU's will get an IP address on the same network as Dom0. If a DHCP server provides addresses, it needs to be configured to give addresses to the guests. Another networking type can be selected by editing /etc/xen/xend-config.sxp

Configuring Remote Management

The following remote management options are available:

  • Create SSH keys for root, and use ssh-agent and ssh-add before launching virt-manager.
  • Set up a local certificate authority and issue x509 certs to all servers and clients. For information on configuring this option, refer to http://libvirt.org/remote.html.

Building a Fedora Guest System

The installation of Fedora guests using anaconda is supported. The installation can be started on the command line via the virt-install program or in the GUI program virt-manager.

Building a Fedora Guest System using virt-install

Start the interactive install process by running the virt-install command-line program:

su -c "/usr/sbin/virt-install"

Enter the root password when prompted.

The following questions about the new guest OS will be presented. This information can also be passed as command line options; run with an argument of --help for more details. In particular, kickstart options can be passed with -x ks=options.

  1. What is the name of your virtual machine? This is the label that will identify the guest OS. This label will be used for various virsh commands and also appear in virt-manager the Gnome-panel Xen applet.
  2. How much RAM should be allocated (in megabytes)? This is the amount of RAM to be allocated for the guest instance in megabytes (eg, 256). Note that installation with less than 256 megabytes is not recommended.
  3. What would you like to use as the disk (path)? The local path and file name of the file to serve as the disk image for the guest (eg, /home/joe/xenbox1). This will be exported as a full disk to your guest.
  4. How large would you like the disk to be (in gigabytes)? The size of the virtual disk for the guest (only appears if the file specified above does not already exist). 4.0 gigabytes is a reasonable size for a "default" install
  5. Would you like to enable graphics support (yes or no): Should the graphical installer be used?
  6. What is the install location? This is the path to a Fedora installation tree in the format used by anaconda. NFS, FTP, and HTTP locations are all supported. Examples include:
    • nfs:my.nfs.server.com:/path/to/test2/tree/
  7. http://my.http.server.com/path/to/tree/
Note.png
Installation must be a network type. It is not possible to install from a local disk or CDROM. It is possible, however, to set up an installation tree on the host OS and then export it as an NFS share.

The installation will then commence. If graphics were enabled, a VNC window will open and present the graphical installer. If graphics were not enabled, the standard text installer will appear. Proceed as normal with the installation.

Building a Fedora Guest System using virt-manager

Start the GUI Virtual Machine Manager by selecting it from the "Applications-->System Tools" menu, or by running the following command as root:

su -c "virt-manager"

Enter the root password when prompted.

  1. Open a connection to a hypervisor by choosing File-->Open connection...
  2. Choose "qemu" for KVM, or "Xen" for Xen.
  3. Choose "local" or select a method to connect to a remote hypervisor
  4. After a connection is opened, click the new icon next to the hypervisor, or right click on the active hypervisor and select "New" (Note - the new icon is going to be improved to make it easier to see)
  5. A wizard will present the same questions as appear with the virt-install command-line utility (see descriptions above). The wizard assumes that a graphical installation is desired and does not prompt for this option.
  6. On the last page of the wizard there is a "Finish" button. When this is clicked, the guest OS is provisioned. After a few moments a VNC window should appear. Proceed with the installation as normal.

Building a Fedora Guest System using 'cobbler' and 'koan'

Cobbler is a tool for configuring a provisioning server for PXE, Xen, and existing systems. See http://cobbler.et.redhat.com for details. The following instructions are rather minimal and more configuration options are available.

First, set up a provisioning server:

su -c "yum install cobbler"
man cobbler # read the docs!
cobbler check # validate that the system is configured correctly
cobbler distro add --name=myxendistro --kernel=/path/to/vmlinuz --initrd=/path/to/initrd.img
cobbler profile add --name=myxenprofile --distro==myxendistro [--kickstart=/path/to/kickstart] 
cobbler list # review the configuration
cobbler sync # apply the configuration to the filesystem

Alternatively, cobbler can import a Fedora rsync mirror and create profiles automatically from there. Some of the imported distros will be Xen profiles and some will be for bare metal. Usage of the Xen profiles will be required. See the manpage for details.

cobbler import --mirror=rsync://your-fedora-mirror --mirror-name=fedora
cobbler sync

On the system that will host the image:

su -c "yum install koan"
koan --virt --profile=myxenprofile --server=hostname-of-cobbler-server

After Installation

When the installation of the guest operating system is complete, it can be managed using the GUI virt-manager program or on the command line using virsh.

Managing Virtual Machines graphically with virt-manager

Start the GUI Virtual Machine Manager by selecting it from the "Applications-->System Tools" menu, or by running the following command:

virt-manager

{1} If you are not root, you will be prompted to enter the root password. ChooseRun unprivileged to operate in a read-only non-root mode.

  • Choose "Local Xen Host" and click "Connect" in the "Open Connection" dialog window.
  • The list of virtual machines is displayed in the main window. The first machine is called "Domain 0"; this is the host computer.
  • If a machine is not listed, it is probably not running. To start up a machine select "File-->Restore a saved machine..." and select the file that serves as the guest's disk.
  • The display lists the status, CPU and memory usage for each machine. Additional statistics can be selected under the "View" menu.
  • Double click the name of a machine to open the virtual console.
  • From the virtual console, select "View-->Details" to access the machine's properties and change its hardware configuration
  • To access the serial console (if there is a problem with the graphical console) select "View-->Serial Console"

For further information about virt-manager consult the project website

Bugs in the virt-manager tool should be reported in BugZilla against the 'virt-manager' component

Managing Virtual Machines from the command line with virsh

Virtual machines can be managed on the command line with the virsh utility. The virsh utility is built around the libvirt management API and has a number of advantages over the traditional Xen xm tool:

  • virsh has a stable set of commands whose syntax and semantics are preserved across updates to the underlying virtualization platform.
  • virsh can be used as an unprivileged user for read-only operations (e.g. listing domains, listing domain statistics).
  • virsh can manage domains running under Xen or KVM with no perceptible difference to the user


Note.png
A valid URI must be passed to virsh. For details, see http://libvirt.org/uri.html

To start a virtual machine:

su -c "virsh -c <URI> create <name of virtual machine>"

To list the virtual machines currently running:

su -c "virsh -c <URI> list"

To gracefully power off a guest:

su -c "virsh -c <URI> shutdown <virtual machine (name | id | uuid)>"

To save a snapshot of the machine to a file:

su -c "virsh -c <URI> save <virtual machine (name | id | uuid)> <filename>"

To restore a previously saved snapshot:

su -c "virsh -c <URI> restore <filename>"

To export the configuration file of a virtual machine:

su -c "virsh -c <URI> dumpxml <virtual machine (name | id | uuid)"

For a complete list of commands available for use with virsh:

su -c "virsh help"

Or consult the manual page: man 1 virsh

Bugs in the virsh tool should be reported in BugZilla against the 'libvirt' component.

Managing Virtual Machines from the command line with qemu-kvm

KVM virtual machines can also be managed in the command line using the 'qemu-kvm' command. See man qemu-kvm for more details.

Troubleshooting

SELinux

The SELinux policy in Fedora has the neccessary rules to allow use of Xen with SELinux enabled. The main caveat to be aware of is that any file backed disk images need to be in a special directory - /var/lib/xen/images. This applies both to regular disk images, and ISO images. Block device backed disks are already labelled correctly to allow them to pass SELinux checks.

Log files

There are two log files stored on the host system to assist with debugging Xen related problems. The file /var/log/xen/xend.log holds the same information reported with 'xm log. Unfortunately these log messages are often very short and contain little useful information. The following is the output of trying to create a domain running the kernel for NetBSD/xen.

[2005-06-27 02:23:02 xend]  ERROR (SrvBase:163) op=create: Error creating domain:(0, 'Error')
Traceback (most recent call last):
File "/usr/lib/python2.4/site-packages/xen/xend/server/SrvBase.py", line 107, in _perform
val = op_method(op, req)
File "/usr/lib/python2.4/site-packages/xen/xend/server/SrvDomainDir.py", line 71, in op_create
raise XendError("Error creating domain: " + str(ex))
XendError: Error creating domain: (0, 'Error')

The second file, /var/log/xen/xend-debug.log usually contains much more detailed information. Trying to start the NetBSD/xen kernel will result in the following log output:

ERROR: Will only load images built for Xen v3.0
ERROR: Actually saw: 'GUEST_OS=netbsd,GUEST_VER=2.0,XEN_VER=2.0,LOADER=generic,BSD_SYMTAB'
ERROR: Error constructing guest OS

When reporting errors, always include the output from both /var/log/xen/xend.log and /var/log/xen/xend-debug.log.

If starting a fully-virtualized domains (ie to run unmodified OS) there are also logs in /var/log/xen/qemu-dm*.log which can contain useful information.

Finally, hypervisor logs can be seen by running the command

xm dmesg

Serial Console

Host serial console access

For more difficult problems, serial console can be very helpful. If the Xen kernel itself has died and the hypervisor has generated an error, there is no way to record the error persistently on the local host. Serial console lets you capture it on a remote host.

The Xen host must be setup for serial console output, and a remote host must exist to capture it. For the console output, set the appropriate options in /etc/grub.conf:

title Fedora
root (hd0,1)
kernel /vmlinuz-current.running.version com1=38400,8n1 sync_console
module /vmlinuz-current.running.version ro root=LABEL=/ rhgb quiet console=ttyS0 console=tty pnpacpi=off
module /initrd-current.running.version

for a 38400-bps serial console on com1 (ie. /dev/ttyS0 on Linux.) The "sync_console" works around a problem that can cause hangs with asynchronous hypervisor console output, and the "pnpacpi=off" works around a problem that breaks input on serial console. "console=ttyS0 console=tty" means that kernel errors get logged both on the normal VGA console and on serial console. Once that is done, install and set up ttywatch to capture the information on a remote host connected by a standard null-modem cable. For example, on the remote host:

su -c "ttywatch --name myhost  --port /dev/ttyS0"

Will log output from /dev/ttyS0 into a file /var/log/ttywatch/myhost.log

Paravirt guest serial console access

Para-virtualized guest OS will automatically have a serial console configured, and plumbed through to the Domain-0 OS. This can be accessed from the command line using

su -c "virsh console <domain name>"

Alternatively, the graphical virt-manager program can display the serial console. Simply display the 'console' or 'details' window for the guest and select 'View -> Serial console' from the menu bar.

Full Virt guest serial console access

Fully-virtualized guest OS will automatically have a serial console configured, but the guest kernel will not be configured to use this out of the box. To enable the guest console in a Linux fully-virt guest, edit the /etc/grub.conf in the guest and add 'console=ttyS0 console=tty0'. This ensures that all kernel messages get sent to the serial console, and the regular graphical console. The serial console can then be access in same way as paravirt guests:

su -c "virsh console <domain name>"

Alternatively, the graphical virt-manager program can display the serial console. Simply display the 'console' or 'details' window for the guest & select 'View -> Serial console' from the menu bar.

Accessing data on a guest disk image

There are two tools which can help greatly in accessing data within a guest disk image: lomount and kpartx.

Stop (medium size).png
Remember never to do this while the guest is up and running, as it could corrupt the filesystem
  • lomount
su -c "lomount -t ext3 -diskimage /xen/images/fc5-file.img -partition 1 /mnt/boot"

lomount only works with small disk images and cannot deal with LVM volumes, so for more complex cases, kpartx (from the device-mapper-multipath RPM) is preferred:

  • kpartx
su -c "yum install device-mapper-multipath"
su -c "kpartx -av /dev/xen/guest1"
add map guest1p1 : 0 208782 linear /dev/xen/guest1 63
add map guest1p2 : 0 16563015 linear /dev/xen/guest1 208845

Note that this only works for block devices, not for images installed on regular files. To use file images, set up a loopback device for the file first:

su -c "losetup -f"
/dev/loop0
su -c "losetup /dev/loop0 /xen/images/fc5-file.img"
su -c "kpartx -av /dev/loop0"
add map loop0p1 : 0 208782 linear /dev/loop0 63
add map loop0p2 : 0 12370050 linear /dev/loop0 208845

In this case we have added an image formatted as a default Fedora install, so it has two partitions: one /boot, and one LVM volume containing everything else. They are accessible under /dev/mapper:

su -c "ls -l /dev/mapper/ | grep guest1"
brw-rw---- 1 root disk 253,  6 Jun  6 10:32 xen-guest1
brw-rw---- 1 root disk 253, 14 Jun  6 11:13 guest1p1
brw-rw---- 1 root disk 253, 15 Jun  6 11:13 guest1p2
su -c "mount /dev/mapper/guest1p1 /mnt/boot/"

To access LVM volumes on the second partition, rescan LVM with vgscan and activate the volume group on that partition (named "VolGroup00" by default) with vgchange -ay:

su -c "kpartx -a /dev/xen/guest1"
su -c "vgscan"
Reading all physical volumes.  This may take a while...
Found volume group "VolGroup00" using metadata type lvm2
su -c "vgchange -ay VolGroup00"
2 logical volume(s) in volume group "VolGroup00" now active
su -c "lvs"
LV        VG         Attr   LSize   Origin Snap%  Move Log Copy%
LogVol00  VolGroup00 -wi-a-   5.06G
LogVol01  VolGroup00 -wi-a- 800.00M
su -c "mount /dev/VolGroup00/LogVol00 /mnt/"
...
su -c "umount /mnt"
su -c "vgchange -an VolGroup00"
su -c "kpartx -d /dev/xen/guest1"
Stop (medium size).png
Note: always remember to deactivate the logical volumes with "vgchange -an", remove the partitions with "kpartx -d", and (if appropriate) delete the loop device with "losetup -d" after performing the above steps. The default volume group name for a Fedora install is always the same, it is important to avoid activating two volume group of the same name at the same time. LVM will cope as best it can, but it is not possible to distinguish between these two groups on the command line. In addition, if the volume group is active on the host and the guest at the same time, it can cause filesystem corruption.

Getting Help

If the Troubleshooting section above does not help you to solve your problem, check the Red Hat Bugzilla for existing bug reports on Xen in Fedora. The product is "Fedora", version is whatever version of Fedora you are running and the component is "kernel" for bugs related to the xen kernel and "xen" for bugs related to the tools. These reports contain useful advice from fellow xen testers and often describe work-arounds.

For general Xen issues and useful information check the Xen project documentation , and mailing list archives .

Finally, discussion on Fedora Xen support issues occur on the Fedora Xen mailing list

References

Footnotes