From Fedora Project Wiki

Line 33: Line 33:
{{admon/note|iSCSI target|Internet Small Computer System Interface, an Internet Protocol (IP)-based storage networking standard for linking data storage facilities. An iSCSI target is often a dedicated network-connected hard disk storage device, but may also be a general-purpose computer}}
{{admon/note|iSCSI target|Internet Small Computer System Interface, an Internet Protocol (IP)-based storage networking standard for linking data storage facilities. An iSCSI target is often a dedicated network-connected hard disk storage device, but may also be a general-purpose computer}}
=== Setup ===
=== Setup ===
* have virtual machine ready
* have virtual machine (VM) ready
* prepare iSCSI volume on another VM which is reachable from VM where the installation will be performed
* prepare iSCSI volume on another VM (called here <code>iSCSI_target</code> VM) which is reachable from VM where the installation will be performed
 
 
<b> On <code>iSCSI_target</code> VM do </b>
{{admon/important|Firewall settings|Ensure, '''port 3260''' is available for incoming connection and there is no blocking firewall in the way between target and test machine.}}
* install <code>scsi-target-utils</code> package
    # yum install scsi-target-utils
* add new iSCSI target, target ID 1
* add new iSCSI target, target ID 1
     # tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2009-02.com.example:auth.chap
     # tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2009-02.com.example:auth.chap
* Add a new iSCSI logical unit with lun 1 to specific target with tid=1.
* Add a new iSCSI logical unit with lun 1 to specific target with tid=1.
     # tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/loop0
     # tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/loop0

Revision as of 06:54, 18 May 2013

General Instructions

  • follow steps in use cases
  • when you are busy then take use-case with the fewest attendee
  • fill the report in this form [1]
  • after the report from thus event are collected, QE team will work with UDX team on qualitative and quantitative analysis, share the results with developers and reports bugs/rfes in Bugzilla, in addition summary will be sent to all the contributors

Who's available

The following cast of characters will be available testing, workarounds, bug fixes, and general discussion ...


Initial setup

  • have a Fedora 19 Beta RC2 (virtual) machine owned by you, ISO image available at [2] or [3]
  • alternatively you can use prepared image available at [4]

Text mode installation

  • Install Fedora using text mode (append text on kernel command line)
  • Text mode installation will offer you possibility to continue installation remotely using VNC, please don't use it and continue in the text mode
  • In the installer add new user john with admin rights

Create multiple Volume Groups

Important.png
Multiple hard drives required
You need a machine with more than 4 disks

Action

  • Start Fedora 19 installation in graphical mode (default)
  • Use manual partitioning, choose LVM partitioning scheme
  • Create four volume groups, one volume group per disk drive
  • Create four mountpoints: /, /var, /tmp, /home and place each of them to separate volume group
  • Place swap partition to the same volume group as /

CHAP authentication against iSCSI target

Note.png
CHAP
Challenge-Handshake Authentication Protocol (CHAP) authenticates a user or network host to an authenticating entity
Note.png
iSCSI target
Internet Small Computer System Interface, an Internet Protocol (IP)-based storage networking standard for linking data storage facilities. An iSCSI target is often a dedicated network-connected hard disk storage device, but may also be a general-purpose computer

Setup

  • have virtual machine (VM) ready
  • prepare iSCSI volume on another VM (called here iSCSI_target VM) which is reachable from VM where the installation will be performed


On iSCSI_target VM do

Important.png
Firewall settings
Ensure, port 3260 is available for incoming connection and there is no blocking firewall in the way between target and test machine.
  • install scsi-target-utils package
   # yum install scsi-target-utils
  • add new iSCSI target, target ID 1
   # tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2009-02.com.example:auth.chap
  • Add a new iSCSI logical unit with lun 1 to specific target with tid=1.
   # tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/loop0
  • Add the address to the access lists of the target, allow connection from all initiators
   # tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL
  • Setup new user "consumer" with password "Longsw0rd"
   # tgtadm --lld iscsi --op new --mode account --user consumer --password Longsw0rd
  • Bind newly created user to iSCSI target with tid=1
   # tgtadm --lld iscsi --op bind --mode account --tid 1 --user consumer