From Fedora Project Wiki

m (Lruzicka moved page User:Lruzicka/QA:Testcase pipewire cli to QA:Testcase PipeWire PipeWire CLI: The test case has been approved for wider use.)
Line 5: Line 5:
== Setup ==
== Setup ==


# This test case should be performed on '''bare-metal machines'''.
# This test case should be performed on '''bare-metal''' machines. To be able to test with '''virtual''' machines, consider a [https://fedoraproject.org/wiki/QA:Howto_USB_Passtrough USB device pass-through].
# The computer must be '''equipped with a sound device and a microphone''' (or another input source of audio).
# The computer must be '''equipped with a sound device and a microphone''' (or another input source of audio).
# Install a desktop version of '''Fedora 34''' (or later).
# Install a desktop version of '''Fedora 34''' (or later).

Revision as of 18:16, 23 February 2021

PipeWire CLI tools

This test case tests that PipeWire can be controlled using CLI commands.

Setup

  1. This test case should be performed on bare-metal machines. To be able to test with virtual machines, consider a USB device pass-through.
  2. The computer must be equipped with a sound device and a microphone (or another input source of audio).
  3. Install a desktop version of Fedora 34 (or later).
  4. Install the pipewire-utils package.
  5. Connect your speakers (headphones) to the default sound device.
  6. Have an audio file in the wav format at your disposal. If you do not have one, you can download a suitable audio file. Some default files can also be found in the /usr/share/sounds/ directory.
  7. Perform the following test case as a regular user.

How to test

  1. List all available playback devices (targets) and check that all your output sound devices are listed.

    $ pw-cat -p --list-targets

    Note that each target has an identification number assigned. The default target is marked with an asterisk (*). Check that it matches your default audio device.

  2. Play a wav sound file over the default target and check that it is correctly played over the default sound device.

    $ pw-cat -p <audiofile.wav>

  3. Play a wav sound file while setting the volume to a low level. Check that the playback is quieter when compared to the previous step.

    $ pw-cat -p --volume=0.1 <audiofile.wav>

  4. List all available recording devices (targets) and check that all your input sound devices are listed.

    $ pw-cat -r --list-targets

  5. Connect your microphone (or another input source of audio) to the default input sound device.

  6. Record a sample recording using your default sound device. Check that it has been correctly recorded. Use the playback command used in Step 2.

    $ pw-cat -r audiotest.wav

  7. Record a sample recording using a different volume level. Check that it has been correctly recorded. Compare the volume level with the first recordings and make sure this one is much quieter.

    $ pw-cat -r --volume=0.1 quiet.wav

  8. Record a sample recording using a different rate. Check that it has been correctly recorded. Compare the quality with the first recording and check that this recording sounds less clean and has an overall "lower" quality.

    $ pw-cat -r --rate=6000 lowrate.wav

  9. If you have more than one audio devices, you can repeat the previous steps with another device using the --target option, such as

    $ pw-cat -p --target=XX <audiofile> or $ pw-cat -r --target=XX <audiofile>

    where XX stands for the device number obtained by the --list-targets option.

  10. Alternatively, you can use dedicated commands to play and record audio, i.e. pw-play and pw-record.

Expected results

  1. Playback targets are listed and they correspond to your audio devices.
  2. Audio files can be played and recorded using the pw-cat command or its dedicated variants.
  3. Connected output and input sound devices work.