From Fedora Project Wiki

No edit summary
m (adding category for modularity acceptance test cases)
 
(15 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{QA/Test_Case
{{QA/Test_Case
|description= Install, remove and udpate modules in Fedora Server
|description=This test case proves that a module can be installed on the system.
|setup=  
|setup=To test this feature:
# Grab Fedora Server and continue to install on a VM or Baremetal
# Install a '''clean''' Fedora.
# Login as root or run the following with <code>sudo</code>
|actions=
|actions=
=== Install Modules <code>foo</code> from Stream and profile: ===
# Open a terminal session, either use terminal or a virtual console.
    # Run <code> dnf module install foo:stream/profile </code>
# List available modules using <code>dnf module list</code> and choose one of them to do the next step. Find out if the module has a '''default stream''' and a '''default profile''' set. Based on this, follow one of the scenarios. When you attempt to install a module without  a default stream or profile, omitting to specify the stream or profile in the installation command will only result in enabling that module. Pay attention to this and always use the appropriate command.
# Install a module following one of the scenarios:
## Install the module using the module's default stream and profile <code>dnf module install <module></code>.
## Install a module without a default stream, or choose a non-default stream using <code>dnf module install <module>:<stream></code>.
## Install a module without a default profile, or choose a non-default profile using <code>dnf module install <module>:<stream>/<profile></code>.
# List the enabled modules <code>dnf module list --enabled</code>.
# List the installed modules <code>dnf module list --installed</code>.
# Check that packages were really installed <code>rpm -qa <module></code>.
# If the installed module was an application or a service, try to run it.
|results=
The following requirements must be met:
# All installation commands must run without errors.
# All installation commands must result in packages installed on the system.
# The installed module must be listed in both '''--enabled''' and '''--installed''' lists.
# <code>rpm -qa <module> </code> must return the installed package with the same version as declared by the module.
# If the module was an application or a service, it should attempt to start.
# Using <code>dnf module install <module>:<stream></code> should be enough to install every module.


=== Install module <code>foo</code> with Profile, Stream and Version ===
'''Note:''' All modules should have a '''default profile''' and they should be able to install using <code>dnf module install <module>:<stream></code>. If a module does not have a default profile set, report a bug for it.
        # Run <code> dnf module isntall foo:stream:version/profile </code>
|optional=


=== Remove module <code>foo</code> with Profile, Stream and Version: ===
}}
        # Run <code> dnf module remove foo:stream:version/profile </code
|results=
The commands execute without error
# The first command will ask you to install the package , if installed it will output
# The second command will install the package from the desired stream , if the desired stream doesn't match the current stream , it will ask to switch stream                                                                                                                                                                   
# The install with stream:version/profile will output this ===
# The remove module command will output the following.


}}
[[Category:Modularity_Acceptance_Test_Cases]]

Latest revision as of 19:15, 10 February 2022

Description

This test case proves that a module can be installed on the system.

Setup

To test this feature:

  1. Install a clean Fedora.

How to test

  1. Open a terminal session, either use terminal or a virtual console.
  2. List available modules using dnf module list and choose one of them to do the next step. Find out if the module has a default stream and a default profile set. Based on this, follow one of the scenarios. When you attempt to install a module without a default stream or profile, omitting to specify the stream or profile in the installation command will only result in enabling that module. Pay attention to this and always use the appropriate command.
  3. Install a module following one of the scenarios:
    1. Install the module using the module's default stream and profile dnf module install <module>.
    2. Install a module without a default stream, or choose a non-default stream using dnf module install <module>:<stream>.
    3. Install a module without a default profile, or choose a non-default profile using dnf module install <module>:<stream>/<profile>.
  4. List the enabled modules dnf module list --enabled.
  5. List the installed modules dnf module list --installed.
  6. Check that packages were really installed rpm -qa <module>.
  7. If the installed module was an application or a service, try to run it.

Expected Results

The following requirements must be met:

  1. All installation commands must run without errors.
  2. All installation commands must result in packages installed on the system.
  3. The installed module must be listed in both --enabled and --installed lists.
  4. rpm -qa <module> must return the installed package with the same version as declared by the module.
  5. If the module was an application or a service, it should attempt to start.
  6. Using dnf module install <module>:<stream> should be enough to install every module.

Note: All modules should have a default profile and they should be able to install using dnf module install <module>:<stream>. If a module does not have a default profile set, report a bug for it.